weber.fix plus - บริษัท แซง-โกแบ็ง เวเบอร์. จำกัด ผู้นำและผู้เชี่ยวชาญระดับโลกด้านกาวปูกระเบื้อง ยาแนวกระเบื้อง และกันซึมกับสาขา 43 ประเทศทั่วโลก

SUBSTRATE

Not suitable to use on internal and external floors (instead use weber.tai fix or weber.tai gres).
Not suitable to use for tiling in a very humid or wet area e.g. swimming pool (instead use weber.tai gres).
Not suitable to use on external walls (instead use weber.tai flex).
Not suitable to use on metal or plastic substrates (instead use weber.color poxy).weber.tai flex

Principal components: acrylic resins, re-dispersion mineral filler, polymer agents.

Temperature resistance: -20°C to +80°C
Maximum weight of tiles for vertical application: 30 kg/m²
Bonding strength at dry stage: > 1 N/mm² (MPa)
Bonding strength in water immersion: > 0.5 N/mm² (MPa)
Density: 1.75 g/cm³
- Note: These test values were performed on laboratory samples. Site mixes may show slight differences in performances due to methods of application and site conditions

For new substrate: it should be flat, hard, level, dry, and clean with normal absorption.
For old substrate: scrape off any peel-off coatings or remove any de-bonding tiles and do the re-tiling.
Clean the surface until free from grease, dust, or any stains.
In case of new screed or render, the substrate should be fully cured for 7 days per 1 cm thickness of concrete before tiling.
In case of flexible or bendable substrates; gypsum board, gypsum-fiber board for instance; it is recommended to frame and brace them with screw for every area of 900 cm2 (30 x 30 cm.).

Tiles should not be immersed in water because it will decrease bonding strength of the adhesive.
Ensure that tiles are clean, dry, free from grease, dust, or any other contaminations.

weber.fix plus is a ready-to-use tile adhesive, no water required. Just mix the product until a homogeneous paste.
After proper mix, the product should be left for 3 to 4 minutes before using in order to get the complete chemical reaction.

Apply some paste adhesive on the wall, and then use a notched trowel to equally spread the adhesive horizontally on the area of 1 - 2 m².
- The depth of the notched trowel is to control the constancy and quantity of adhesive.
In case of tile size exceeding 25 x 25 cm (10" x 10"), it is recommended to have adhesive buttered onto the tile back in order to ensure the overall covering of the adhesive onto substrate and also to prevent voids after fixing tiles on the substrate, which could make tiles being fragile and allow water permeation.
Lay tiles on the paste adhesive and press firmly or knock gradually with rubber hammer in order to spread the notch of adhesive equally and ensure a good contact.
Leave clearance joints, at least 2 mm, for grouting.
- Carefully clean of any excess adhesive on the tiles and joints with a damp sponge when the adhesive is still wet.
Any adjustments can be done within 10 to 20 minutes before weber.fix plus sets.
Wait for 24 hours before grouting to let the adhesive dry.
- Weber grouting products are available in many ranges of color and applications depending on the joint width and working conditions.

Avoid applying the adhesive in lumps (as shown in the picture) at the tile back. This will create voids underneath the tiles, which could lead to the tile fragility and water permeation.
Avoid using the adhesive on red-hot substrates or the substrates exposing to direct sunlight.

To maintain straight joints, spacers should be used (as shown in the picture). The joint width is controlled by the width of spacer.
To avoid water leakage into underneath tiles and to avoid tile movement when there is foot traffic, the joint width is recommended to be at least 1.5 mm for wall and at least 3 to 20 mm for floor.
In case of clay tiles or porous tiles, weber.klin tec should be used before grouting to protect the tile surfaces from grout-color stains.
In bathroom and kitchen, weber.color power or weber.color classic before applying withweber.klin jcr is recommended for grouting to protect the joints from fungus, dirt, soap stains, or cooking-oil stains.

One year after manufacturing date if unopened and stored in dry and ventilated place (store airtight after opened)

Additional information